Machine Category : Gear Machines
Sub - Category : Gear Generator Straight Bevel
+ Advance Filter
MAKE
MODEL
GEAR DIA MM from to
MODUL MM from to
Total machines found : 41
Sr. ID Make Model Description YOM Condition Photo Enquire
1 MA27324 WMW Modul ZFTK500 X 10 Max wheel diameter : 500 mm,
Gear width : 50 mm,
Max module : 10,
Min module : 1,
Total power requirement : 15 kW,
Machine Weight : 10 t.
1971 Good Condition Photo
2 MA26951 Nihonkikai B800 Max diameter : 800 mm,
Max. module : 25 mm
Good Condition Photo
3 MA26897 WMW Modul ZFTKK500x10/1 Work piece diameter : 500 mm,
Module : 13 mm,
Tooth depth : 25 mm,
Tooth width : 71 mm,
Number of teeth : 6-100,
Distance work piece spindle/top of cone : 80-450 mm,
Pitch cone length : 200 mm,
Total connected load : 18 kW,
machine weight : 9000 kg,
Quantity : 4 nos,
There's one set of change gears for all 4 machines.
1970-s (aprox.1973-1974) Excellent condition,under power Photo
4 MA26628 Gleason USA 26 Maximum Diameter Gear : 825 mm,
Cone Distance Max (30 deg. and 450 mm Cutter) : 412 mm,
Max. Pitch Angle : Shaft at 90 Deg : 84 Deg 216 mm,
Min. Pitch Angle: 5 Deg : 504 mm,
Extreme Ratio : 10:1
Max Face Width : 100 mm,
Diametral Pitch : 1 1/2,
Diameter of Taper Hole at Large End : 152 mm,
Taper Per Foot : 19 mm,
Depth of Taper : 152 mm,
Diameter of Hole Through : 127 mm,
Spindle Nose to Machine Center : 235 mm,
Cutter Diameter : 225 x 300 x 400 x 450 mm,
Max Offset Above Center : 112 mm,
Max Offset Below Center : 112 mm,
Max. Distance from Machine Center to Nose of Spindle : 587 mm,
Min. Distance from Machine Center to Nose of Spindle : 125 mm,
Cutter Speeds-Feed Per Minute : 35 - 200,
Feed (sec./tooth) : 23 - 333,
Main Motor - 2 Speed : 7 1/2 HP,
Floor Space : 3300 x 2525 mm,
Net Weight : 25,300 lbs.

EQUIPMENT:
Workholding Fixture
Drawbar
Change Gears
Coolant System
Photo
5 MA25650 Russian CT267 Max. diameter : 320 mm,
Max. modul : 8 mm,
Overall dimensions : 2885 x 2570 x 19995 mm,
Machine weight : 8,75 tons.
1992 Good Condition Photo
6 MA25481 Gleason USA 725 Capacity :
Root angle max. : 55 deg,
Root angle min : 15 deg,
Pitch diameter,
Semi automatic : 152 mm,
Automatic
Chute : 152 mm,
Gear and pinion hopper : 102 mm,
Shank length (maximum loader stripping height ) : 102 mm,
Gear and pinion hoppe r: 38 mm,
Depth max.
21" cutters : 14.8 mm,
Face width at root max.
21" cutters : 28 mm,
Index range : 8-50,
Work spindle (configuration)
Diameter of taper hole at large end : 99 mm,
Taper per foot : 15.4 mm,
Depth of taper : 15.8 mm,
Depth of counterbore behind tape r: 57.2 x 77.9 mm,
Diameter of hole through spindle : 22.3 mm,

Feeds and Speeds :
Cutter speeds
21" Cutters : 32.9-51 M/min,
Feeds (seconds per tooth)
21" cutters : 2.0-3.1

Electrical equipment:
Main drive motor : 10 hp at 1500 rpm,
Hydraulic motor : 71/2 hp at 1500 rpm,
Cutting oil pump (built in motor ) : 2 hp at 3000 rpm,
Chip screw motor : 1/4 hp at 1500 rpm,

Miscellaneous:
Floor space
Manual : 3200 x 2210 mm,
Automatic (max. required) : 3200 x 2261 mm,
Approx. net weight
Automatic machine : 8,750 kg,
Approx.shipping weight ,box ed export,
Automatic machine 9920 kg.
With Cutter Heads.
Good Condition Photo
7 MA25396 Heidenreich & Harback 160K Max gear dia :-
Ratio 1:1 - 1320 mm,
Ratio 1:8 - 1650 mm,
Min gear dia :-
Ratio 1:1 - 200 mm,
Ratio 1:8 - 60 mm,
Module : 6~30,
Max tooth width : 250 mm,
Max / Min ram stroke : 280 / 80 mm,
Max / Min pitch cone length : 935 / 140 mm,
Max pitch cone angle : 90 degrees,
Number of strokes, 12 steps : 12.5 ~ 160 / min,
Bore in indexing head spindle : 140 mm,
Distance from front edge tool to spindle nose : 270 ~ 1000 mm,
Total power requirement( 4 motors ) : 7.5 kW,
Full set of change gears.
1970 Good Condition Photo
8 MA25017 Gleason USA 726 Root angle range 15-55 deg,
Pitch diameter manual : 152 mm,
Depth 21 inch seperate roughing and finishing 14.8 mm,
Depth 21 inch complete 10.7 mm,
Face width at root 21 inch cutters 28 mm,
Index range 8-50, Work spindle,
Diameter of tapered hole at large end 99.22 mm,
Taper per foot : 15.48 mm,
Depth of taper : 15.8 mm,
Counterbore behind taper : 57.2 x 77.9 mm,
Diameter of hole through spindle 22.3 mm,
Feeds and speeds, Cutter speeds 21 inch cutters 107-163 FT,
Feeds 21 inch cutters 2.0-3.1 sec,
Main drive motor 10HP : 1800 RPM,
Hydraulic motor 7.5HP : 1800 RPM,
Cutting oil pump - 2HP : 3600 RPM,
Chip screw motor -1/4HP : 1800 RPM,
Machine dimensions L x W automatic : 3.2 x 2.26 mm,
Machine weight manual : 7484 kg.
Equipped with :- Extra cutters and tooling, Auto lub, Coolant system,
Motor and push button controls, Parts counter, Quantity : 2 no.
1976 Photo
9 MA25012 Karats,Japan Max dia : 700 mm,
Max modul : 22,
Good condition,under power Photo
10 MI5776 Russian Diameter : 500 mm, Module : 8. Excellent Photo
11 MA24708 Nihonkikai B600 Max Diameter : 600 mm,
Max Module : 20,
No accessories, no tools.
working condition ,under power Photo
12 MA24031 Oerlikon 4A dia 1600 mm , transversal module of gear cut 30 mm , dimensions of tooth cut : height 66 mm , face width 270 mm , pitch cone distance of gear cut 800 mm , number of teetch cut 10-300, extreme gearing ratio of gear pair cut (at 90 deg between gears axes) 10:1 , angle of pitch cone 5 deg can be inspected under power Photo
13 MA23260 Gleason USA 726 Root angle range 15-55 deg, Pitch diameter manual : 152 mm, Depth 21 inch seperate roughing and finishing 14.8 mm, Depth 21 inch complete 10.7 mm, Face width at root 21 inch cutters 28 mm, Index range 8-50, Work spindle, Diameter of tapered hole at large end 99.22 mm, Taper per foot : 15.48 mm, Depth of taper : 15.8 mm, Counterbore behind taper : 57.2 x 77.9 mm, Diameter of hole through spindle 22.3 mm, Feeds and speeds, Cutter speeds 21 inch cutters 107-163 FT, Feeds 21 inch cutters 2.0-3.1 sec, Main drive motor 10HP : 1800 RPM, Hydraulic motor 7.5HP : 1800 RPM, Cutting oil pump - 2HP : 3600 RPM, Chip screw motor -1/4HP : 1800 RPM, Machine dimensions L x W automatic : 3.2 x 2.26 mm, Machine weight manual : 7484 kg. Equipped with :- Extra cutters and tooling, Auto lub, Coolant system, Motor and push button controls, Parts counter. Good Condition Photo
14 MA23231 Gleason USA 725 Root angle range : 15-55 deg,
Pitch diameter - manual : 150 mm,
Pitch diameter - automatic z chute : 125 mm,
Pitch diameter - automatic gear / pinion hopper : 100 mm,
Shank length - loader stripping height : 100 mm,
Shank length - gear and pinion hopper * : 37.5 mm,
(* can be extended in some cases)
Depth 21 inch separate roughing and finishing : 14625 mm,
Depth 21 inch completing : 10500 mm,
Face width at root - 21 inch cutters : 25 mm,
Index range : 8-50,
Feeds and Speeds cutter speeds 21 inch cutters : 107-163 ft/min,
32.6-49.7m/min,
Work Spindle :
Work Spindle Diameter taper hole large end : 97.65 mm,
Taper per foot : 15.23 mm,
Depth of Taper : 40 mm,
Diameter of Hole Through Spindle : 21.87 mm,
Speed of Countershaft RPM : 400,
Horsepower of motor : 10hp,
Floor Space Required : 3150 mm x 2225 mm,
Net Weight : 19,300 lbs.


Good Condition Photo
15 MA22900 Gleason USA 726 Root angle range 15-55 deg,
Pitch diameter manual : 152 mm,
Depth 21 inch seperate roughing and finishing 14.8 mm,
Depth 21 inch complete 10.7 mm,
Face width at root 21 inch cutters 28 mm,
Index range 8-50,
Work spindle,
Diameter of tapered hole at large end 99.22 mm,
Taper per foot : 15.48 mm,
Depth of taper : 15.8 mm,
Counterbore behind taper : 57.2 x 77.9 mm,
Diameter of hole through spindle 22.3 mm,
Feeds and speeds,
Cutter speeds 21 inch cutters 107-163 FT,
Feeds 21 inch cutters 2.0-3.1 sec,
Main drive motor 10HP : 1800 RPM,
Hydraulic motor 7.5HP : 1800 RPM,
Cutting oil pump - 2HP : 3600 RPM,
Chip screw motor -1/4HP : 1800 RPM,
Machine dimensions L x W automatic : 3.2 x 2.26 mm,
Machine weight manual : 7484 kg.
Equipped with :-
Extra cutters and tooling,
Auto lub,
Coolant system,
Motor and push button controls,
Parts counter.
1991 Good Condition Photo
16 MA22899 Gleason USA 726 Root angle range 15-55 deg,
Pitch diameter manual : 152 mm,
Depth 21 inch seperate roughing and finishing 14.8 mm,
Depth 21 inch complete 10.7 mm,
Face width at root 21 inch cutters 28 mm,
Index range 8-50,
Work spindle,
Diameter of tapered hole at large end 99.22 mm,
Taper per foot : 15.48 mm,
Depth of taper : 15.8 mm,
Counterbore behind taper : 57.2 x 77.9 mm,
Diameter of hole through spindle 22.3 mm,
Feeds and speeds,
Cutter speeds 21 inch cutters 107-163 FT,
Feeds 21 inch cutters 2.0-3.1 sec,
Main drive motor 10HP : 1800 RPM,
Hydraulic motor 7.5HP : 1800 RPM,
Cutting oil pump - 2HP : 3600 RPM,
Chip screw motor -1/4HP : 1800 RPM,
Machine dimensions L x W automatic : 3.2 x 2.26 mm,
Machine weight manual : 7484 kg.
Equipped with :-
Extra cutters and tooling,
Auto lub,
Coolant system,
Motor and push button controls,
Parts counter.
1991 Good Condition Photo
17 MA22255 Gleason USA 710 Cone distance (min-max) 0 - 107 mm,
Root angle - (min-max) - 8-90 deg.,
Extreme ratio, max - 6:1,
Diametral Pitch 6,35 Mod.(4DP),
Index range - 9-120 inclusive,
Pitch diameter, max - 215 mm,
Face width - 35 mm,
Std. diameter of taper hole at large end - 58,34 mm,
Taper depth - 15,87 mm,
Planing cutter speeds - 80-465 strokes/min,
Feeds (sec/tooth) - 10-86,
Main motor - 2HP, 1500 rpm,
Variable feed motor - 1HP, 180-1620 rpm,
Hydraulic pump motor - 1HP, 1500 rpm,
Coolant pump motor - HP, 3000 rpm,
Dimentions - 2032 x 1524 x 1626 mm,
Weight - 5000 kg (11000 lbs).
Good Condition Photo
18 MA20945 WMW Modul ZFTK500 X 10 Dia. 500 mm, Modul 10, Qty : 3 Nos. Good Condition Photo
19 MA20757 Russian 5A250 Max module 8 mm

Max diameter of the workpiece 500 mm

Main drive power 3 kW

Dimentions (L x W x H) 2200 x 1600 x 1600

Weight 8000 kg



Accesoires

20 pieces knifes
60 pieces change gears
Cooling system
Good condition,under power Photo
20 MA19629 Russian 5A283C1 D 1600 mm,

B 800 mm,

M 30,

Machine weight 19 tons.
1974 Complete Photo
21 MA19288 Magg Germany SD32X Max wheel diameter: 320 mm, Gear width: 200 mm, Max module: 12, Min module: 1, Number of teeth: 10-150, Grinding wheel diameter: 200/280 mm, Feeds axial: 100- 1800 mm/min, Base circle diameter: 20 mm, Grinding wheel hole diameter: 90 mm, Machine dimension: 2200x4800x3100 mm, Machine weight: 6 ton. 1979 Good Condition Photo
22 MA18969 Russian 5C286 Max.pich diameter of gear cut: 800 mm,
Max. transversal module of gear cut: 16 mm,
Max angle of cradle rolling 60 deg.,
Table:
Max. distance over which table is withdrawn into extreme non working position 130 mm,
Speeda and Feeds:
Max. cutter sttroke 180 mm,
Range of cutter double strokes per minute 28-270,
Range of angular feed rates in generating 0.15-2.8 deg/s,
Cutting time per tooth 12-200 s,
Workhead:
Range of workhead setting angles 5-90 deg,
Range of distance from workhead spindle nose to machine centre line 135-600 mm,
Max workhead swivel axis displacement from zero position :
towards cradle 30 mm,
from cradle 65 mm,
Taper of workhead spindle hole Metric 160,
Workhead spindle through hole diameter 125 mm,
Drive, overall Dimensions and Mass:
Number of electric motor installed 5,
Electric motors:
main drive 3-ph AC electric motor:
- Power 7.5 kW,
- Rotation frequency 1500min-1,
Feed drive DC electric motor:
- Power 2.2 kW,
- Rotation frequency 1500 min-1,
Total power of electric motors installed 13.2 kW,
Machine overall dimensions witout chip seperators 3235 x 2180 x 2200 mm,
Pump plant overall dimensions 840 x 630 x 2310 mm,
Machine mass 15000 kg.

Complete,working condition Photo
23 MA18374 Russian 5C277P Max. Diam. 500 mm
Max. modul. 12 mm
Maximum width of tooth: 80 mm
Min/max. no. of teeth: 10 - 150

Weight machine 15100 kg

- 2 machines
Good Condition Photo
24 MA18281 Gleason USA Maximum Cone distance : 457 mm,
Minimum Cone Distance : 0
Largest Pitch Angle, Angular Gear : 90 deg.,
Largest Pitch Angle, Shafts @ 90 deg. : 84 deg.18',
Smallest Pitch Angle, shafts @ 90 deg. : 5 deg.42',
Extreme Ratio, shafts @ 90 deg. : 1-1/4 DP,
Index Range 10 to 100 inclusive and most numbers 200,
Largest Pitch Diameter(10:1 Ratio) Gear/Pinion: 784mm-79mm,
Largest Pitch Diameter(2:1 Ratio) Gear/Pinion: 705mm-352mm,
Largest Pitch Diameter(1:1 Ratio) Gear/Pinion: 555mm)-555mm,
Work Spindle Diameter taper hole large end : 152 mm,
Taper per foot : 19 mm,
Depth of Taper : 152 mm,
Diameter of Hole Through : 127 mm,
Spindle Nose to Center Line : 127- 660 mm,
Cutter Speeds 13 speeds: 18-110 strokes/min,
Feeds 22 feeds: 24-686 sec/tooth,
Horsepower of Motor : 7.5 HP,
Hydraulic Pump Motor : 1200 rpm,
Cutting Oil Pump Motor : 1/2 HP,
Floor Space Required : 1879 2667 mm,
Net Weight : 24,900 lbs. : 11279 kg.
Machine Is Equipped With The Following:
-Misc Change Gears
-Books / Manuals
Good Condition Photo
25 MA18134 Russian CT267 diameter up to 800mm, modul to 16mm 1988 Not Working Photo
26 MA18121 Gleason USA 14 Max Cone Dist 305mm,
Max Cone Dist (1" Face)................ 11 1/8"
Max Cone Dist (1" Face)................ (282.5mm),
Min Cone Distance0"/(0mm),
Max Pitch Angle (Angular Gears) 105 DEGREES,
Max Pitch Angle (90-Deg Shafts84 DEGS/18Min.,
Min Pitch Angle 5 DEG/42Min.
Max Ratio 10/1
Max Pitch Diameter (SEE TABLE)
Max Face Width 3.5"/(89mm)
Max Stroke Length5" 4.5"
Max Stroke Length (127-114.3mm)
Index Range5-100 Incl(+Up To 200)
(More Teeth Are Recommended For Better Design)
Max 3 DP (Nom)
Max Pitch8.5 Module)
Dia Hole In Work Spdl (Large End) 3.906"
Dia Hole In Work Spdl (Large End)99.2mm,
Spindle Taper Per Foot 5.5mm,
Depth Of Spindle Taper 152.4mm,
Dia Of Spindle Thru-Hole 7.7mm,
Spdl Nose To Ctr Line2.5 To 15"
Spdl Nose To Ctr Line63.5 To 381mm,
Thirteen (13) Tool Spds In SPM 64 To 495
Sixteen (16) Fds From 10 Sec To 2 Min
Sixteen (16) Fds From11 Sec Per Tooth
Floor Space Required 76" x 56"
Floor Space Required 1930x1420mm,
Machine Net Weight, (Approx.) 13,600 LBS.
Machine Net Weight, (Approx.) (6,863 Kg)

NOTE: Suitable For The Cutting Of Straight Bevel
Gears & Pinions Up To 24" (630mm) Diameter, 3.5"
(89mm) Face-Width, & 3 DP (Module 8.5)
FEATURES / EQUIPMENT:
Hydraulic Work Chucking Cylinder, w/Draw In Bar
& Nuts
Stock Dividing Gauge
Upper & Lower Tool Setting Gauge w/Proof Block
Cutter Length Gauge
Standard Tool-Holders
Extended Tool-Holders
Good Assortment Of Change Gears
Index Hand Crank
Roughing Yoke & Bushing
3 HP, 3PH, 50/60 CY, 220/440 V, 1740 RPM Main
Drive Motor
1.5 HP, 3PH, 50/60 CY, 220/440 V, 1140 RPM
Hydraulic Pump Motor
O.5 HP, 3PH, 50/60 CY, 220/440 V, 3450 RPM
Coolant Pump Motor
Guards, Covers
Complete Electrical Controls
Operators Manual, Parts List, Wiring & Hydraulic
Diagrams


Good Condition Photo
27 MA17362 Gleason USA 605 max gear dia 340 mm, max gear module 10 - 2 machines 1976 excellent working condition Photo
28 MA17254 Gleason USA 726 Max. height of teeth 14,8 mm,
Max. external of workpiece 152 mm,
Max. external of workpiece, w. automatic loading device 102 mm,
Root angle, min. / max. 15 / 44 ,
Tooth width 28 mm,
No. of teeth 8 - 50,
Cutter speeds 32.6 - 49.7 mm,
Workpiece feeds per tooth 2 -3.1 sec Workspindle bore 22 mm,
Total electrical load, approx. 20 kW - 380 V - 50 Hz,
Weight 9,500 kg,
Automatic roughing and finishing cycles,
Automatic workpiece loading device.
Various tools and other accessories.
Coolant device, etc.
1987 Very good condition Photo
29 MA17184 Klingenberg German AFK201 Max. Module 8 mm,
Tooth width 70 mm,
Working 540 mm,
Milling spindel speeds 38/150 min,
Milling spindle:
Cone 50,
Adjustability 36 mm,
Milling slide:
Speeds 38-150 min,
Swiveling until 360,
Spindle of tool piece:
For bevel gear 130h6mm,
Drilling 90,45H6,
Swiveling until 90,
Distance cone tip-cone edge 42 - 275 mm,
Cooling pump, centrifugal 80 l/min,
Electrical power 12,4 kW,
Weigth: 8,5 t,
Space requirement (LxBxH) 2,6x3,2x2,25 m.
1970 Good Condition Photo
30 MA16929 Gleason USA 109 max. wheel diameter 254 mm,
gear width 32 mm,
cone distance min./max. 127 mm,
ratio 5 : 1,
min/max. pitch cone angle 10 - 80 ,
tooth width 32 mm,
range of tooth size 15 mm,
no. of teeth 8 - 75,
workpiece spindle - bore 58341 mm,
depth of taper 1524 mm,
spindle bore diameter 508 mm,
shaft length - max. 63 mm,
total power requirement ca. 10 kW,
weight of the machine ca. 8,2 t,
dimensions of the machine ca. 2,16 x 2,95 x 2,60 m.
1996 Good Condition Photo
31 MA16770 Russian 5C276P Max dia of workpiece 500 mm, max outer circular module 10 mm, max outer cone distance 250 mm, max face width 80 mm, max pitch cone angle 5 degree , number of workpiece teeth 10-150 , dia of tapered hole in workhead spindle 100 mm, distance between workhead spindle face and machining center 75-375 mm, type of gear cutting tools 3 , frequency of double strokes of sliders 48-400 db.st/min , angular speed of generating feed 0,3-6,0 deg/s, feed at radius of 800 mm/min , overall dimensions of machine separately installed equipment 3400 x 3300 x 1995 mm, machine weight with separately installed equipment 9.395 tons, For Worm & Hypoid Gears 1985 Good Condition Photo
32 MA16706 Russian CT267 For combined or separate finishing or roughing of bevel gears with straight teeth.
Max working diameter 320 mm
Module 8 mm
Number of teeth 10 - 150
Dimensions 2885 х 2570 х 1995 mm
Weight 8,75 tons
Qty: 3 Nos. 2 Pcs of 1987 & 1 Pcs. of 1991.
1987 & 1991 Good Condition Photo
33 MA16705 Russian 5C276P Max dia of workpiece 500 mm, max outer circular module 10 mm, max outer cone distance 250 mm, max face width 80 mm, max pitch cone angle 5 degree , number of workpiece teeth 10-150 , dia of tapered hole in workhead spindle 100 mm, distance between workhead spindle face and machining center 75-375 mm, type of gear cutting tools 3 , frequency of double strokes of sliders 48-400 db.st/min , angular speed of generating feed 0,3-6,0 deg/s, feed at radius of 800 mm/min , overall dimensions of machine separately installed equipment 3400 x 3300 x 1995 mm, machine weight with separately installed equipment 9.395 tons, For Worm & Hypoid Gears 1985 Good Condition Photo
34 MA15197 Russian 5C276P Max dia of workpiece 500 mm, max outer circular module 10 mm, max outer cone distance 250 mm, max face width 80 mm, max pitch cone angle 5 degree , number of workpiece teeth 10-150 , dia of tapered hole in workhead spindle 100 mm, distance between workhead spindle face and machining center 75-375 mm, type of gear cutting tools 3 , frequency of double strokes of sliders 48-400 db.st/min , angular speed of generating feed 0,3-6,0 deg/s, feed at radius of 800 mm/min , overall dimensions of machine separately installed equipment 3400 x 3300 x 1995 mm, machine weight with separately installed equipment 9.395 tons, For Worm & Hypoid Gears 1984 Good Condition Photo
35 MA14736 Gleason USA G710W Dia 215 mm,

Teeth Width 35.5 mm,

Modul 6.35 mm,

Machine weight 15 tons.
Good Condition Photo
36 MA13382 Russian 5C276P Max dia of workpiece 500 mm, max outer circular module 10 mm, max outer cone distance 250 mm, max face width 80 mm, max pitch cone angle 5 degree , number of workpiece teeth 10-150 , dia of tapered hole in workhead spindle 100 mm, distance between workhead spindle face and machining center 75-375 mm, type of gear cutting tools 3 , frequency of double strokes of sliders 48-400 db.st/min , angular speed of generating feed 0,3-6,0 deg/s, feed at radius of 800 mm/min , overall dimensions of machine separately installed equipment 3400 x 3300 x 1995 mm, machine weight with separately installed equipment 9.395 tons, For Worm & Hypoid Gears 1991 Good Condition Photo
37 MA13241 Russian 5C276P Max dia of workpiece 500 mm, max outer circular module 10 mm, max outer cone distance 250 mm, max face width 80 mm, max pitch cone angle 5 degree , number of workpiece teeth 10-150 , dia of tapered hole in workhead spindle 100 mm, distance between workhead spindle face and machining center 75-375 mm, type of gear cutting tools 3 , frequency of double strokes of sliders 48-400 db.st/min , angular speed of generating feed 0,3-6,0 deg/s, feed at radius of 800 mm/min , overall dimensions of machine separately installed equipment 3400 x 3300 x 1995 mm, machine weight with separately installed equipment 9.395 tons, For Worm & Hypoid Gears 1983 Good Condition Photo
38 MA12275 Russian 5C276P Max dia of workpiece 500 mm, max outer circular module 10 mm, max outer cone distance 250 mm, max face width 80 mm, max pitch cone angle 5 degree , number of workpiece teeth 10-150 , dia of tapered hole in workhead spindle 100 mm, distance between workhead spindle face and machining center 75-375 mm, type of gear cutting tools 3 , frequency of double strokes of sliders 48-400 db.st/min , angular speed of generating feed 0,3-6,0 deg/s, feed at radius of 800 mm/min , overall dimensions of machine separately installed equipment 3400 x 3300 x 1995 mm, machine weight with separately installed equipment 9.395 tons, For Worm & Hypoid Gears 1989 Complete Photo
39 MA7033 Russian ST280 Max. workpiece dia 800 mm (865), max. mean normal module 14 mm, max. whole tooth depth 38 mm, max. pitch cone radius 412 mm, max. width of face 125 mm, min. pitch angle 5 degrees, no. of teeth of the workpiece 5-100, max. hypoid offset 75 mm, dia of tapered hole in workhead spindle 153 mm, distance between workhead spindle face and machine centre max. 600 mm, min 120 mm, nominal dia of gear-shaping cutter heads 160-500 mm, max. radius between the tool spindle and the cradle centreline 360 mm, speed of tool spindle rotation 15-163 rpm, angular rate of roll feed, 0.2-0.3 degrees/seconds, rating of primary motion electric motor 6.0/6.2 kW, overall dimensions of the machine-tool with separately installed hydraulic power station and electric equipment cabinet 3615 x 2970 x 2375 mm, max. weight of the machine-tool 18500 kg, Hypoid gear New Photo
40 MA502 5C276P Max dia of workpiece 500 mm, max outer circular module 10 mm, max outer cone distance 250 mm, max face width 80 mm, max pitch cone angle 5 degree , number of workpiece teeth 10-150 , dia of tapered hole in workhead spindle 100 mm, distance between workhead spindle face and machining center 75-375 mm, type of gear cutting tools 3 , frequency of double strokes of sliders 48-400 db.st/min , angular speed of generating feed 0,3-6,0 deg/s, feed at radius of 800 mm/min , overall dimensions of machine separately installed equipment 3400 x 3300 x 1995 mm, machine weight with separately installed equipment 9.395 tons, For Worm & Hypoid Gears Photo
41 MA14 5C276P Max dia of workpiece 500 mm, max outer circular module 10 mm, max outer cone distance 250 mm, max face width 80 mm, max pitch cone angle 5 degree , number of workpiece teeth 10-150 , dia of tapered hole in workhead spindle 100 mm, distance between workhead spindle face and machining center 75-375 mm, type of gear cutting tools 3 , frequency of double strokes of sliders 48-400 db.st/min , angular speed of generating feed 0,3-6,0 deg/s, feed at radius of 800 mm/min , overall dimensions of machine separately installed equipment 3400 x 3300 x 1995 mm, machine weight with separately installed equipment 9.395 tons, For Worm & Hypoid Gears Photo



G-59/60, E Block, Simla House, Nepean Sea Road, Mumbai 400036. India.
Phone : +91-22-66644462 /63 /69     Fax : +91-22-23690034
E-mail : info@nvmachinery.com / info@machineworld.in